M-Audio TDIF-Interface mit 24Bit/96kHz Analog and Digital i/O Delta TDIF Spécifications Page 1

192 I/O™

192 I/O Guide4

Chapter 2: 192 I/O Overview 5chapter 2192 I/O OverviewThis chapter describes the front and back panel features of the 192 I/O. 192 I/O Front PanelPowe

192 I/O Guide6Loop Master LEDThe LOOP MASTER LED indicates which Pro Tools|HD audio interface is the master Pro Tools peripheral. The Loop Master LED

Chapter 2: 192 I/O Overview 7192 I/O Back PanelAlthough the 192 I/O is a 16-channel audio in-terface, it has up to 50 inputs and outputs avail-able th

192 I/O Guide8Input TrimsTwo dedicated Input Trims per analog input channel provide further calibration options and flexibility. Depending on how you

Chapter 2: 192 I/O Overview 9Enclosure ConnectorsThe right half of the back panel of 192 I/O fea-tures a set of non-removable connectors that are moun

192 I/O Guide10EXT. CLOCK In and OutThe External Clock I/O ports are standard BNC connectors that receive and output a word clock signal. These ports

Chapter 2: 192 I/O Overview 11Legacy and Expansion Peripheral Port LimitationsBecause both the Legacy port and the Expansion port use channels 17–32,

192 I/O Guide12Soft Clip LimitingThe 192 I/O provides an optional “soft” limiter for each input. The Soft Clip limiter can be used to attenuate incomi

Appendix A: Adding or Removing I/O Cards 13appendix aAdding or Removing I/O CardsThe 192 I/O comes with one available expan-sion bay on the back of th

Legal NoticesThis guide is copyrighted ©2007 by Digidesign, a division of Avid Technology, Inc. (hereafter “Digidesign”), with all rights reserved. Un

192 I/O Guide144 Lift off the top of the 192 I/O and set it aside.5 Remove the five screws on the cover over the empty bay. Do not misplace these sc

Appendix A: Adding or Removing I/O Cards 1510 Locate the raised ridge in the middle of the 50-pin cable which connects to the 192 I/O chassis. This r

192 I/O Guide16Hardware Setup Changes After Adding a CardThe additional inputs and/or outputs provided by the new card will appear in the Hardware Set

Appendix A: Adding or Removing I/O Cards 176 Pull the card out by gripping the edges be-tween your thumb and forefinger. Pull straight back, lifting

192 I/O Guide18

Appendix B: Pinout Diagrams for the DB-25 Connectors 19appendix bPinout Diagrams for the DB-25 ConnectorsAnalog Output DB-25 Analog Input (+4 dBu) DB-

192 I/O Guide20Analog Input (–10dB(V)) DB-25 AES/EBU DB-25 MH2CH1_COLDCH1_HOTCH2_GNDCH2_COLDCH3_GNDCH3_HOTCH3_COLDCH4_GNDCH4_HOTCH4_COLDCH8_COLDCH7_C

Appendix B: Pinout Diagrams for the DB-25 Connectors 21TDIF DB-25GND_AGND_AGND_C22PF22PFGND_CMH2CH12_RCV_DATAGND3CH56_RCV_DATACH12_XMT_DATACH78_RCV_DA

192 I/O Guide22

Appendix C: 192 I/O Calibration Mode Instructions 23appendix c192 I/O Calibration Mode InstructionsBefore you use the 192 I/O audio interface, you may

Important Safety InstructionsWhen using electric or electronic equipment, basic precautionsshould always be followed, including the following:• Read a

192 I/O Guide24Digital With a digital recording device such as the 192 I/O, in order to allow for headroom, you must align a 0 VU tone from the consol

Appendix C: 192 I/O Calibration Mode Instructions 2513 Create an additional mono Auxiliary Input track for each input you want to calibrate. Set the

192 I/O Guide26When you have properly aligned the incoming peak signal levels to match the calibration refer-ence level, both Automatch indicator arro

Index 27Symbols+4 dBu 7, 8, 11Numerics–10 dBV 7, 8, 11192 I/OBack Panel 7Front Panel 5Overview 596 I/O and level calibration 26AA/D converters 7AC Pow

192 I/O Guide28EAES/EBUAES/EBU 9EnclosureOptical (ADAT) 9Connectors 9ExpansionDigiLink 10Peripheral Port Limitations 11port 10expansion bay 13External

Index 29SS/PDIF In/Out 9Sample Rate 5conversion 8conversion, AES/EBU 12conversion, Optical (ADAT) 12conversion, TDIF and Optical (ADAT) 12Session 6Sof

DIGIDESIGN2001 Junipero Serra BoulevardDaly City, CA 94014-3886 USATel: 650.731.6300Fax: 650.731.6399TECHNICAL SUPPORT (USA)Tel: 650.731.6100Fax: 650.

Contents vcontentsChapter 1. Introduction to the 192 I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1What’s Incl

192 I/O Guidevi

Chapter 1: Introduction to the 192 I/O 1chapter 1Introduction to the 192 I/OThe Digidesign 192 I/O™ 16-channel digital au-dio interface is for use in

192 I/O Guide2System RequirementsThe Digidesign 192 I/O requires a Digidesign-qualified Pro Tools|HD system. Compatibility InformationDigidesign can o

Chapter 1: Introduction to the 192 I/O 3About www.digidesign.comThe Digidesign website (www.digidesign.com) is your best source for information to hel